Wuxi Guanya Refrigeration Technology co., ltd

Thermal oil secondary circulation system safety knowledge

The thermal oil secondary circulation system is equipped with various instruments and equipment for temperature control. After market research, carefully research and production of temperature-controlled products, when using, you need to pay attention to its safety knowledge, safer use of thermal oil secondary circulation system.

LNEYA heat transfer oil secondary circulation system uses branded fully enclosed compressors with advanced performance and reliable quality. The relay, protector and capacitor used in the refrigeration unit of the heat transfer oil secondary circulation system are all original high-quality equipment, ensuring reliable performance and long service life. It integrates cooling, heating and circulation, and the power is reasonable and saves space.

Liquid medium should be added in the tank before use. Generally, the liquid level is 30mm-50mm below the working surface to prevent the heater from being burnt. The power supply is 220VAC/50Hz, and the equipment must have good grounding. The circulating pump of the heat transfer oil secondary circulation system is automatically opened when the equipment starts to operate, and the refrigeration compressor will make corresponding start or stop command operation according to the temperature of the equipment unless there is a special need.

LNEYA heat transfer oil secondary circulation system adopts the automatic control function of circulating pump, that is, when the equipment is running, the circulation pump runs automatically. When the equipment is running, because of the function of the self-contained circulation pump, the liquid surface will show a flowing pattern if running. When there is no obvious flow state at the liquid tank interface, it means that there may be a helium state, and it should be exhausted in time. With its own cooling function, the cooling function can automatically issue a running or stop command according to the temperature of the device, or it can artificially prohibit the compressor from running through the system parameters. When the device prohibits the compressor from running, the compressor needs to be set again to restore normal cooling. run.

The secondary circulation system of the heat transfer oil shall be placed in a ventilated and dry place, and the back and sides shall be separated from the obstacle by more than 300 mm. The secondary circulation system of the heat transfer oil is used, the power switch is turned off, and the power plug is unplugged. If it is not used for a long time, the liquid in the tank should be drained and scrubbed clean.

When the heat transfer oil secondary circulation system is used, it is necessary to pay more attention to the above problems in order to achieve more efficient operation efficiency.


Related News
Related Products
  • SLJ -110℃~-150℃

    SLJ -110℃~-150℃

    January 11, 2018Temperature ranges from - 5 ~ - 150 ℃, can meet different temperature; Adopt environmental protection refrigerants; Famous brand semi-closed piston compressor, semi-closed bipolar piston compressor, semi-hermetic screw compressor, main brand are BOCK.view
  • Single Fluid Heat Transfer System SR

    Single Fluid Heat Transfer System SR

    April 10, 2018Working temperature range from -25℃to 200℃, other temperature range need to set to the widest temperature range(-50℃to 250℃) Centralized control of 2~20 reactors, each reactor's and jacket temperature can be set independently. One system control multipleview
  • Reactor Temperature System ZLF

    Reactor Temperature System ZLF

    April 10, 2018A set of cooling heat exchanger, heat exchanger, through proportional adjusting valve control cold heat into the heat exchanger, then through the uniform medium input to the reactor jacketed to do heat exchange and temp. Control, system has inside expansiview
  • LT -45℃~30℃

    LT -45℃~30℃

    April 10, 2018Low Temperature Cooling Chiller LT model: LT-5018N,LT-5040N,LT-5062N,LT-5090N,LT-50A1N,LT-50A2N; Medium Temperature Range: -45℃~30℃. ASET multifunctional controller, control outlet temperature of water tankview
  • TES -45℃~250℃

    TES -45℃~250℃

    February 28, 2019-45℃~+200℃ 2.5kW~25kW ±0.3℃view
  • TES -85℃~200℃

    TES -85℃~200℃

    February 28, 2019Temperature control range:-85 ° C ~ 200 ° CPower range:2.5kW~25kWTemperature control accuracy:±0.3°CModelTES-8525WTES-8555WTES-85A10WTES-85A15WTES-85A25WTemp. Range-85℃~200℃-85℃~200℃-85℃~200℃-85℃~200℃-85℃~200℃Heating P...view
products
Contact
Tel: + 86 18751546043
E-mail: sales@cnzlj.com
Add: No.203, Hongyun Road, Hongshan Street, Optoelectronics Park, Xinwu District, Wuxi City, Jiangsu Province, China
code chat